ATA to IDE Interface PC Card Drives
ATA to IDE Interface PC-104 Module

The Card Master-ATA IDE is a PC card drive which allow PC compatible computer with an IDE controller to use a PCMCIA ATA Flash, ATA Hard Disk Drive and Compact Flash. This card drive automatically sets the 68 pins ATA mode of PCMCIA card allowing the system bios to access the card directly as a IDE Drive.

The C.M.-ATA IDE/F comply 3.5" FDD form factor, allow you to mount it in 3.5" FDD bay of computer housing, with 40 pins connector can be connected directly to IDE interface. The ATA devices install as drive C: and do not require card and socket services . The C.M.-ATA IDE/R can be fixed in the rear window of PC as a rear accessed Card reader, the other functionality is exactly the same as C.M.-ATA IDE/F. ATA To IDE products support Linux system & with Hot Swap function w/o driver.

We design the Hot Swap function under Windows98/Me/2000/XP with software which enable users to insert and remove Flash cards & Compact Flash cards without turning off the PC system power, it's a much convenient way for user to use these drives.



  • Supports SATA 1.5/3Gbps interface in host
  • Provides 6 expansion slots, each can support a 4/8/16/32GB SDHC card.
  • Supports SLC NAND Flash memory
  • Maximum capacity: Depends on SDHC capacity
  • Supports all operating systems
  • Size : 100.2 x 69.85 x 9.5 mm


  • ATA to standard IDE interface
  • 1 Front slot
  • 40 Pins IDE and 4 Pins Power Connectors
  • Support Type I/II/III ATA Flash, ATA HDD, Compact
  • Flash Cards(an adaptor required)
  • Standard 3.5" Drive form factor
  • Power Consumption: 5V, 70 mA Typical
  • Operating Temperature: 0oC- 70oC

  • ATA to standard IDE interface
  • 1 real slot
  • 40 Pins IDE and 4 Pins Power Connectors
  • Support Type I/II/III ATA Flash, ATA HDD, Compact
  • Flash Cards(an adaptor required)
  • 1/2 size interface card form factor
  • Power Consumption: 5V, 70 mA Typical
  • Operating Temperature: 0oC- 70oC

  • 2.5" form factor
  • Supports Compact Flash Type I /II (Micro Drive)
  • Support DMA mode
  • One Compact Flash socket
  • Dimensions: 75mm x 10mm x 78mm
  • 44Pin IDE Connector

  • 2.5" form factor
  • Supports Compact Flash Type I /II (Micro Drive)
  • Optional 40 pins IDE and 4 pins power connectors or 44 pins Connector
  • Optional LED possible
  • One Compact Flash socket w/ejector
  • Dimensions: 79.7mm x 70mm x 10.7mm
  • Screw bracket of Rear slot
  • Master/Slave optional
  • Support DMA mode

  • 2.5" form factor
  • 2 Compact Flash slots
  • Supports Compact Flash Type I /II (Micro Drive)
  • Optional 40 pins IDE 180° connector and 4 pins power connectors
  • Dimensions: 81.7mm x 70mm
  • Master/Slave optional
  • Support DMA mode
  • Designed with ejector for both side

  • 2.5" form factor
  • 2 Compact Flash slots
  • Supports Compact Flash Type I /II (Micro Drive)
  • Optional 40 pins IDE 90° connector and 4 pins power connectors
  • Dimensions: 81.7mm x 70mm
  • Master/Slave optional
  • Support DMA mode
  • Designed with ejector for both side

  • Can be mounted on 3.5" form factor
  • 2 Compact Flash slots
  • Supports Compact Flash Type I /II (Micro Drive)
  • Optional 40 pins IDE and 4 pins power connectors and (or) 44 pins Connector
  • Dimensions: 81.7mm x 70mm
  • Master/Slave optional
  • Support DMA mode
  • Designed with ejector for both side
  • Strong Suggest use same brand of CF cards

  • Can be mounted on 3.5" form factor
  • 2 Compact Flash slots
  • Supports Compact Flash Type I /II (Micro Drive)
    Optional 40 pins IDE and 4 pins power connectors
  • Dimensions: 81.7mm x 70mm
  • Master/Slave optional
  • Support DMA mode
  • Designed with ejector for both side.
  • Support Hot Swap function with Software

  • ATA to standard IDE interface.
  • 1 Front Slot.
  • Supports Compact Flash Type I II (Micro Drive)
    Through 50-pin Compact Flash connector directly (Adapter not required).
  • 40 pins IDE and 4 pins power connectors.
  • 5V, 70mA power consumption. (typical)
  • Can be mounted on 3.5" Drive bay.
  • Dimensions: 109.6 x 101.6 x 25.4mm.
  • With special design hardware circuit support " Hot Swap " function.

  • ATA to standard IDE interface 2 Front Slot
    Supports Type I/II ATA Flash, ATA HDD and Type I/II Compact Flash Cards through 68-pin PCMCIA connector & 50-pin Compact Flash connector
  • 5V, 70mA power consumption. (typical)
  • Can be mounted on 3.5" Drive bay.
  • Dimensions: 109.6 x 101.6 x 25.4 m
  • with "Hot Swap" software
  • Support DMA mode (Serial ATA )
  • Without Special cable use normal IDE cable.

  • ATA to standard IDE interface
  • 1 Front Slot
  • 40 pins IDE and 4 pins power connectors
  • Standard 3.5" Drive form factor
  • With special design hardware circuit support Hot Swap Function
  • With "Hot Swap" software

  • ATA to Standard IDE interface.
  • 1 Rear Slot
  • 40 pins IDE & 4 pins power connectors
  • Support Type I/II/III ATA Flash Cards, ATA HDD, Compact Flash Card
  • With special design hardware circuit support Hot Swap function
  • With "Hot Swap" software
  • 5V 70mA power consumption

 

The PCM-212 ATA and PCM-212 C.F. are PC Card Drives which allow PC compatible computer with an IDE controller to use a PCMCIA ATA Flash, ATA Hard Disk Drive and Compact Flash. This Card Drive Module automatically sets 50 pins ATA mode of PCMCIA Card or Compact Flash Card allowing the system bios to access the card directly as a IDE Drive.

The PCM-212 ATA and PCM-212 C.F. comply PC-104 form factor, allow you to mount it with other PC-104 Modules or Single Board PC with 40 pins. connector, it can be connected directly to IDE interface . The ATA devices install as drive C: and do not require card and socket services.



  • ATA to standard IDE interface
  • 1 slot for 68 Pins ATA
  • 40 Pins IDE and 4 Pins Power Connectors
  • Support Type I/II/III ATA Flash, ATA HDD, Compact Flash Cards(an adaptor required)
  • Standard PC-104 form factor
  • Power Consumption: 5V, 70 mA Typical
  • Operating Temperature: 0oC - 70oC

  • ATA to standard IDE interface
  • 1 slot for 50 Pins C.F. Cards
  • 40 Pins IDE and 4 Pins Power Connectors
  • Support Compact Flash Cards
  • Standard PC-104 form factor
  • Power Consumption: 5V, 70 mA Typical
  • Operating Temperature: 0oC - 70oC

  • PCMCIA (ATA) and compact flash (ATA) to standard IDE interface.
  • 1Slot for 68 pins ATA and slot for 50 pins C.F. Cards.
  • 40 pins IDE and 4 pins power connection.
  • Support TYPE I/II/III ATA Flash, ATA HDD, Compact Flash cards.
  • Standard PC-104 form factor
  • Power Consumption : 5V, 70Ma Typical.
 

In this Section, we have on-line catalogs PDF files that can be downloaded. If you don't have an Adobe Acrobat Reader, you can click here and download it from Adobe's WEB Site, then you will be able to read the PDF files that you can download here.